*Now available is the point-to-point, bidirectional, full duplex 1000Base-SX (850 nm Multi-Mode Fiber) Ethernet over SONET Network Interfaces on SST and SHNS.

Qwest currently offers STS-1 and 1+1 & 0X1 OC-3, OC-12, OC-48 and OC-192 Linear interfaces delivered from Fujitsu and Nortel standard OC-3, OC-12, OC-48 and OC-192 SONET Add-Drop Multiplexers (ADMs) as well as Fujitsu and Cisco Next Generation SONET Hybrid (ADM/DCS) equipment.  Tellabs STS-1 interface provided via the Titan 5500 Wideband Digital Cross-connect System (DCS) along with standard DS1 and DS3 interfaces including DS3 Transmux are also supported.

Additionally available are:

• TL1 over 1) 3-layer X.25 (DTE or DCE mode) at 9.6 Kbps (or greater) and 2) TCP/IP 10/100Base-T Ethernet serial interfaces.  These OS management interfaces are limited to SHNS ACCU-Ring and Software Reconfiguration Capability (SRC) applications only.
• Point-to-point, bidirectional Data Communications Channel (DCC) tunnels on standard SONET Optical Carrier (OC-3/12/48/192) Network Interfaces delivered from Cisco Next Generation SONET ADMs.
• Point-to-point, bidirectional, full duplex 10Base-T, 100Base-TX and 1000Base-LX (Single-Mode Fiber) Ethernet over SONET Network Interfaces on SST and SHNS.
• 1+1 OC-3, OC-12, OC-48 and OC-192 UPSR interfaces delivered from Fujitsu and Cisco Next Generation SONET Hybrid (ADM/DCS) equipment.
• SONET Network Interfaces with the following embedded Ethernet payloads:

*Now available is the point-to-point, bidirectional, full duplex 1000Base-SX (850 nm Multi-Mode Fiber) Ethernet over SONET Network Interfaces on SST and SHNS.

These SONET, corresponding OS management, DCC tunnels and Ethernet over SONET interfaces are/will be available in Arizona, Colorado, Idaho, Iowa, Minnesota, Montana, Nebraska, New Mexico, North Dakota, Oregon, South Dakota, Utah, Washington and Wyoming.  Determination is on an Individual Case Basis (ICB) for each customer request, dependent upon where equipment and facilities are available.

Qwest’s SONET-based services are offered under interstate and intrastate tariffs.

1) The SONET standards designate some bits and bytes in the overhead as undefined or unused.  Any interfaces offered as a part of Qwest’s SONET-based services employing nonstandard usage of these bits and bytes must be disclosed.  Vendor specific variations from the ANSI and Telcordia Technologies standards for STS-1 and SONET Optical Carrier Linear and UPSR interfaces are as indicated below for Fujitsu, Nortel, Cisco and Tellabs NEs.

• American National Standards Institute Documents
  Available from ANSI at: http://www.ansi.org/

  ANSI T1.105
  Synchronous Optical Network (SONET) – Basic Description Including Multiplex Structure, Rates, and Formats

  ANSI T1.105.03
  Synchronous Optical Network (SONET) – Jitter at Network Interfaces

• Telcordia Publications
  Available from Telcordia at: http://www.telcordia.com/

  GR-253-CORE
  Synchronous Optical Network (SONET) Transport Systems: Common Generic Criteria

  GR-1377-CORE
  SONET OC-192 Transport System Generic Criteria

  GR-1400-CORE
  SONET Dual-Fed Unidirectional Path Switched Ring (UPSR) Equipment Generic Criteria

The Fujitsu FLASH-192, FLASHWAVE 4100, FLASHWAVE 4500, Cisco ONS 15454 and Tellabs Titan 5500 STS-1, SONET OC-N Linear and UPSR interfaces comply with the above technical specifications. With the DCC tunneling application, the customer’s Section DCC messages will be transparent to and unaffected by the Qwest ONS 15454 network.

• Fujitsu Documents
  Available from Fujitsu at: http://www.fujitsu.com/

  Fujitsu FLM Series SONET Phase II Interface Disclosure
  Technical Information Bulletin G-0264 applicable to FLASHWAVE 4500

• Nortel Documents
  Available from Nortel at: http://www.nortelnetworks.com/

  S/DMS Transport Node OC-3 and OC-12 Network Elements Interface Disclosure
  S/DMS Transport Node OC-48 Network Elements Interface Disclosure

2) TL1 over 3-layer X.25 (DTE or DCE mode) at 9.6 Kbps (or greater) and TCP/IP 10/100Base-T Ethernet serial interfaces for SHNS ACCU-Ring and Software Reconfiguration Capability applications will comply with the following:

• Fujitsu Documents
  Available from Fujitsu at: http://www.fujitsu.com/

  FNC-660-0021-274
  FLASHWAVE 4500 – TL1 Commands

• Cisco Documents
  Available from Cisco at: http://www.cisco.com/

  Cisco ONS 15454 TL1 Command Guide

• Telcordia Publications
  Available from Telcordia at: http://www.telcordia.com/

  GR-253-CORE
  Synchronous Optical Network (SONET) Transport Systems: Common Generic Criteria

  Note: GR-253-CORE requirements for TL1 over X.25 and TCP/IP supersede all other standards documents listed below.

  GR-199-CORE
  Operations Application Messages - Memory Administration Messages

  GR-828-CORE
  Generic Operations Interface – OSI Communications Architecture

  GR-833-CORE
  Network Maintenance: Network Element and Transport Surveillance Messages

  GR-834-CORE
  Network Maintenance: Access and Testing Messages

  TR-TSY-000827
  Generic Operations Interfaces: Non-OSI Communications Architecture

  SR-NWT-002723
  Applicable TL1 Messages for SONET Network Elements

• ITU-T Recommendations
  Available from the International Telecommunication Union at: http://www.itu.int/home/

  Q.811
  Lower Layer protocol profiles for the Q3 and X interfaces

• International Organization for Standardization/International Electrotechnical Commission (ISO/IEC) Documents
  Available from American National Standards Institute at: http://www.ansi.org/
  

  ISO/IEC 8208
  Information technology -- Data communications -- X.25 Packet Layer Protocol for Data Terminal Equipment

• Institute of Electrical and Electronics Engineers Documents
  Available from IEEE at: http://www.ieee.org/portal/site

  IEEE 802.3-2002
  Information technology–Telecommunications and information exchange between systems–Local and metropolitan area networks–Specific requirements–Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications

• SIF/NSIF Documents
  Available from the Alliance for Telecommunications Industry Solutions at: http://www.atis.org/

  NSIF-033
  Requirements for the TCP/IP Protocol Suite on the SONET Access DCN

3) 10Base-T, 100Base-TX, 1000Base-LX (Single-Mode Fiber) and 1000Base-SX Ethernet interfaces on SST and SHNS will conform to the physical layer specifications only in IEEE 802.3-2002.

• Institute of Electrical and Electronics Engineers Documents
  Available from IEEE at: http://www.ieee.org/portal/site

  IEEE 802.3-2002
  Information technology–Telecommunications and information exchange between systems–Local and metropolitan area networks–Specific requirements–Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications

4) SONET STS-1, OC-3, OC-12, OC-48 and OC-192 interfaces with embedded 10Base-T, 100Base-TX and 1000Base-LX/SX Ethernet payloads will additionally comply with these documents.

• Internet Engineering Task Force Request For Comments (RFC)
  Available from IETF at: http://www.ietf.org/

  RFC 2615
  PPP over SONET/SDH

  RFC 3518
  Point-to-Point Protocol (PPP) Bridging Control Protocol (BCP)

  RFC 1841
  PPP Network Control Protocol for LAN Extension

  RFC 1662
  PPP in HDLC-like Framing

• ITU-T Recommendations
  Available from the International Telecommunication Union at: http://www.itu.int/home/

  G.7041/Y.1303
  Generic Framing Procedure (GFP)

• Fujitsu Documents
  Available from:
  Senior Director Contracts Management
  Fujitsu Network Communications
  2801 Telecom Parkway
  Richardson, TX 75082
  800-777-FAST (3278)

  PDD-6979
  Ethernet over SONET Service Feature Requirements Specification

• Cisco Documents
  Available from Cisco at: http://www.cisco.com/

  DOC-7815242
  Cisco ONS 15454 Reference Manual

Any Customer Premises Equipment vendor/manufacturer or Enhanced Services Provider wanting to offer products or services in conjunction with these SONET and corresponding OS management interfaces offered by Qwest may request additional information by contacting:

Jeff Falk
Services Planner – DS3, SONET, DWDM & Ethernet
Phone: (612)-663-3647